System updates

We’re experiencing issues that may affect your Square services. We’ll continue to update our status page with more information.

Home>Square Reader

Square Reader Troubleshooting

Before setting up your Square Reader, make sure you have a compatible device with the latest version of the Square app.

My Square Reader keeps disconnecting

Your Square Reader may have entered a low power state

To conserve battery, your Square Reader will automatically enter a low power state if it hasn’t taken a payment for awhile.

Square Reader (1st generation) will go into a low power state and will remain connected to your device for 8 hours as long as the reader is within 3 metres of the device. Any interaction with the reader through Point of Sale will wake it up from this low power state. The reader will power off completely after 8 hours of inactivity. After this point, you will need to press the button on the reader to reconnect.

Square Reader (2nd generation) will go into a low power state and will remain connected to your device for 30 days as long as the reader is within 3 metres of the device. Any interaction with the reader through Point of Sale will wake it up from this low power state. The reader will power off completely after 30 days of inactivity. After this point, you will need to press the button on the reader to reconnect.

To turn on your Square Reader, press the button on your Square Reader once and wait a few seconds for it to reconnect. You should see 1-4 green lights flash depending on your Square Reader battery level.

Close and reopen the Square app on your device

Restarting the app will allow it to refresh.

Square Reader Range

Your Square Reader must be within three metres of your device. Any further than three metres may mean your Bluetooth connection is out of range and could disconnect.

Check that your Square Reader has adequate battery

Low battery may increase disconnections between your device and Square Reader.

Press the button on your Square Reader once to see the battery level. If you see a blinking red light, that means your Square Reader battery is low and should be charged immediately. If your Square Reader is in a dock, plug the dock’s power cord into a power outlet.

Restart your phone, tablet, or other electronic device

You can also first try briefly putting your device into Airplane mode.

Reset your Square Reader

Hold down the power button on your Square Reader for approximately 20 seconds until you see red lights stop flashing.

Check your Internet connection

Your Square Reader requires a strong and secure Internet connection to take card payments successfully.

Enable Bluetooth from your device settings

For iOS devices, this can be found in Settings > Bluetooth. Try turning Bluetooth off and back on.

For Android devices, navigate to Settings > Connections > toggle on Bluetooth.

Bluetooth will automatically turn off when your Square Reader is connected to a Square Stand by USB cable. Disconnect the USB cable from the Square Stand and then attempt to pair.

Move your Square Reader away from common sources of Bluetooth interference

This includes common household items such as microwave ovens, cordless phones, fluorescent lights, or using your Square Reader on a metal table.

Clear your Bluetooth cache if you have an Android device.

See Apple’s article on Bluetooth interference for additional information.

My Square Reader won’t fit in the Reader Dock

Check Dock Compatibility

There are two generations of Square Reader: Square Reader (1st generation) and Square Reader (2nd generation). If your Square Reader won’t fit into the Dock for Square Reader, identify the generation of your Square Reader and ensure you have the appropriate Dock. Both docks are sold separately via Square Shop.

The Square Reader (2nd generation) is only compatible with the grey Bosstab Dock for Square Reader. The first generation of Square Reader is compatible with both the white Dock for Square Reader that features a micro-USB charging port, and the grey Bosstab Dock for Square Reader.

Square Reader DocksLeft: Square Reader (1st generation) with Dock for Square Reader.
Right: Square Reader (2nd generation) with Bosstab Dock Square Reader (sold separately).

Bosstab Dock

To get started with the Bosstab Dock:

Bosstab Dock Assembly 1

  1. Locate the two buttons on either side of the outside cover. Push the two buttons simultaneously and slide the cover upwards to remove it. 
  2. Place your Square Reader with the card slot facing downwards along the slope. The charging port and power button should be aligned with the higher part of the dock.
    published

Bosstab Dock Assembly 2

  1. Place the outer cover back on until the cover clicks to lock into place.

  1. Plug the power cable to the back of your Square Reader through the access opening in the back of the dock.

Note: The USB cord included with the Square Reader measures 0.8 metres. You can purchase an extended 2.0 metre cable in the
Square Shop.

Dock for Square Reader (1st generation)

Contactless Reader Dock Assembly

To get started with the dock:

  1. Connect the dock’s USB cable to any powered USB port (e.g., wall socket, phone charger, computer).
  2. On the dock, pull up on the clear tab to remove the detachable piece.
  3. Insert the Square Reader making sure it’s fully connected by aligning the micro USB connectors.
  4. Put the detachable piece back to secure the reader in place.
  5. Make sure to connect your reader to your device wirelessly via Bluetooth LE or to the USB hardware hub of Square Stand to start accepting payments. 

Note: The dock’s USB cord measures 1.75 metres. Extender cables aren’t officially supported, so we can’t guarantee compatibility.

My Square Reader won’t pair with my device

Pair your Square Reader with an Android Device

Due to extended security measures, some Android devices will require multiple confirmations during the pairing process with the Square Reader. Follow the prompts on your screen until the “Pair and Connect” banner resolves and you receive confirmation that the connection was successful.

To pair your Square Reader with the Square app:

  1. From the navigation bar at the bottom of your screen, tap ≡ More.
  2. Tap Settings > Hardware > Square Readers.
  3. Tap Connect a Reader.
  4. Tap Pair on the prompt to confirm the Bluetooth pairing request.
  5. On Android devices, quickly tap Pair and Pair & connect each time you are prompted until the connection is successful.

Note: The same prompt may pop up more than once. If the connection fails and you are unable to pair your Android with your Square Reader, try again and make sure to accept all “Pair” prompts within 5 seconds of them appearing on your screen.

Pairing your Square Reader for the first time

Before you attempt to connect your Square Reader, make sure that your Square Reader is ready to be connected.

  1. Enable Bluetooth in your device settings.
  2. If you’re using an iPhone or iPad on iOS 15 or higher, make sure Bluetooth permissions for the Square app are enabled. To do so, on your device, head to Settings > Privacy > Bluetooth and enable permissions for the Square app.
  3. Fully charge your Square Reader.
  4. Check that your device is connected to a secure Internet connection.
  5. Force shutdown your Square Reader:
    • Plug in the Square Reader for at least 20 minutes to be sure it’s charged.
    • Use a small object like a bobby pin, pen cap, or paper clip to firmly press and hold the button on the Square Reader for 20 seconds or after the 4 lights stop blinking red.
    • After 20 seconds, release the button and wait 10 seconds.
    • Press the button again to turn the Square Reader on and observe any lights on the Square Reader.

If the Square Reader lights turn green, you’re all set. If the lights don’t turn on, try again and make sure to firmly press and hold the Square Reader’s button for a full 20 seconds.

Once your Square Reader is ready to be paired, open the Square POS app:

  1. Tap ≡ More from the navigation bar at the bottom of your screen.
  2. Tap Settings > Hardware > Square Readers.
  3. Tap Connect a Reader.Square-Reader-Troubleshooting-US-EN-1

Verify that your Square Reader can go into pairing mode. To put the Square Reader into pairing mode, press the Square Reader’s power button for 3-10 seconds until you see 4 orange blinking lights. Immediately release the power button when you see the 4 orange lights. If you see red lights, you’ve held the button too long and need to try again.

Check out our Troubleshoot your Square Reader YouTube video for additional help.

Pairing your Square Reader with a new device

If you are attempting to pair your Square Reader with a new device or switching the Square Reader to a different device, you must first forget the connection to the previous device. To do so, head to the Square app on the device previously connected to your Square Reader and follow the steps outlined above.

My Square Reader won’t accept card payments

If you are having trouble accepting EMV or tap transactions:

  1. Ensure that your Square Reader is fully charged and that you have a strong Wi-Fi or data connection.
  2. If the Square Reader and device are more than three metres apart, move your Square Reader and device closer when in use.
  3. Verify that your Square Reader is connected to your device:
    • Tap ≡ More from the navigation bar at the bottom of your screen.
    • Tap Settings > Hardware > Square Readers.
    • Check that the four numbers in your settings match the last four digits of your Reader’s serial number. Learn more about identifying your Square Reader’s serial number.
  4. Make sure you press charge in the Square app. You should see a single green light on the Square Reader before you ask your customer to make the payment.
  5. Confirm that your customer’s card has a chip, meaning it’s EMV-enabled. Check that the chip on your customer’s card is facing up.
  6. Keep your customer’s card in the Square Reader until prompted to remove the card.

My Square Reader won’t charge

The tips below usually fix most charging issues customers encounter with the reader:

  • Make sure the Square Reader is firmly plugged into the USB accessory hub of your Square Stand or into a wall powerpoint.
  • Try plugging the power adaptor into a different powerpoint.
  • Force shutdown your reader:
  • Plug in the Square Reader for at least 20 minutes to be sure it’s charged.
  • Use a small object like a bobby pin, pen cap, or paper clip to firmly press and hold the button on the reader for 20 seconds or after the 4 lights stop blinking red.
  • After 20 seconds, release the button and wait 10 seconds.
  • Press the button again to turn the Square Reader on and observe any lights on the reader.

If the Square Reader lights don’t turn on, try again and make sure to firmly press and hold the Square Reader’s button for a full 20 seconds.

Reset Square Reader

If you continue to have trouble with your Square Reader after trying the above steps or if your Square Reader is still connected to another device, you can reset your Square Reader:

  1. Charge your Square Reader for at least 20 minutes.

  2. While the Square Reader is charging, use a small object like a bobby pin, pen cap, or paper clip to firmly press and hold the button on the Square Reader for 20 seconds.

    • After 20 seconds, release the button and wait 10 seconds.

    • Press the button again to turn the Square Reader on and observe any lights on the Square Reader.

If the lights on the Square Reader turn on, you’re all set. If the lights don’t turn on, try again. Make sure to firmly press and hold the Square Reader's button for a full 20 seconds.

Charging and Powering Your Square Devices Safely

Square cables and wall chargers are tested thoroughly and adhere to government standards. To keep you safe and your devices working properly, we recommend you follow these guidelines:

  • Always charge your Square products with the included cable and certified USB charging sources.

  • Store your devices and cables in a safe place away from moisture, extreme temperatures, and debris as these can cause fire, electric shock, injury, or damage to your Square product.

  • Always charge your devices in a dry environment away from all sources of moisture.

  • Inspect your cables and devices for any damage or debris that could interfere with the proper performance of your Square products. If you see any debris or damage to a cable or any connectors, discontinue use and contact Square Support for a replacement.

  • Make sure all connections are fully engaged before charging your device.

  • Always plug and unplug your cables and chargers by holding onto the end of the cable.

  • Keep the connectors free of foreign objects and debris.

  • Always charge your device in a well-ventilated area.

  • If your Square Reader gets wet, immediately power off the device, holding down the power button for at least fifteen seconds. Remove moisture by allowing Square Reader to dry out with the card slot facing down.

Protect Your Square Reader

  • Get the most life out of your Square Reader by avoiding damage to the hardware. Certain attachments and environments can cause damage to Square Reader over time and shorten the lifespan of your device. To protect your Square Reader from everyday wear and tear, we recommend using the compatible cases, accessories, and docks featured in Square Shop. These cases fit a variety of mobile phones and tablets.

  • Avoid using Square Reader in wet environments, and avoid getting water or liquid in the card slot. Taking insert payments with wet payment cards can also cause water damage. 

  • Do not use strong magnets, hook-and-loop fasteners (like Velcro), adhesive, or mounting hardware not tested by Square to frequently mount and unmount Square Reader. The use of third-party accessories not tested by Square to secure Square Reader to surfaces can add tension or pressure to the device, which can cause damage.

  • Move Square Reader away from sources of Bluetooth interference, such as near microwave ovens, cordless phones, fluorescent lights or on a metal table.

Frequently Asked Questions

To learn more, check out our Square Reader FAQ Article. It covers a variety of questions regarding device compatibility, pairing and setting up your device, and taking payments.

Learn more about: Square Hardware

Can't find what you need?